Solidification morphology and phase selection in drop-tube processed Ni–Fe–Si intermetallics

Drop-tube processing was used to rapidly solidify droplets of Ni_64.7Fe₁₀Si_25.3 and Ni_59.7Fe₁₅Si_25.3 alloys. In the larger droplets, and therefore at low cooling rates, only two phases, γ-Ni₃₁Si₁₂ and β₁-Ni₃Si were observed. Conversely, in the smaller droplets, and therefore at higher cooling rates, the metastable phase Ni₂₅Si₉ was also observed. The critical cooling rate for the formation of Ni₂₅Si₉ was estimated as 5 × 10³ K s⁻¹. SEM and TEM analysis reveals three typical microstructures: (I) a regular structure, comprising single-phase γ-Ni₃₁Si₁₂ and a eutectic structure between γ-Ni₃₁Si₁₂ and β₁-Ni₃Si; (II) a refined lamellar structure with a lamellar spacing <50 nm comprising γ-Ni₃₁Si₁₂ and β₁-Ni₃Si; (III) an anomalous structure with a matrix of Ni₂₅Si₉ and only a very small proportion of a second, and as yet unidentified, phase. These results indicate that there is an extended stability field for Ni₂₅Si₉ in the Ni-rich part of the Ni–Fe–Si ternary system in comparison to the Ni–Si binary system. With an increase of cooling rate, an increasing fraction of small droplets experience high undercoolings and, therefore, can be undercooled into the Ni₂₅Si₉ stability field forming droplets consisting of only the anomalous structure (III). The Fe atoms are found to occupy different substitutional sites in different phase, i.e. Fe substitutes for Ni in the γ phase and Si in the L1₂ (β₁) phase respectively.     

Static stress analysis of carbon nano-tube reinforced composite (CNTRC) cylinder under non-axisymmetric thermo-mechanical loads and uniform electro-magnetic fields

Static stresses analysis of carbon nano-tube reinforced composite (CNTRC) cylinder made of poly-vinylidene fluoride (PVDF) is investigated in this study. Non-axisymmetric thermo-mechanical loads are applied on cylinder in presence of uniform longitudinal magnetic field and radial electric field. The surrounded elastic medium is modeled by Pasternak foundation because of its advantages to the Winkler type. Distribution of radial, circumferential and effective stresses, temperature field and electric displacements in CNTRC cylinder are determined based on Mori–Tanaka theory. The detailed parametric study is conducted, focusing on the remarkable effects of magnetic field intensity, elastic medium, angle orientation and volume fraction of carbon nano-tubes (CNTs) on distribution of effective stress. Results demonstrated that fatigue life of CNTRC cylinder will be significantly dependent on magnetic intensity, angle orientation and volume fraction of CNTs. Results of this research can be used for optimum design of thick-walled cylinders under multi-physical fields.     

面向消费类电子产品的自动化生产线成组技术

针对现代消费类电子产品快速更新换代的现状, 介绍了该类产品的自动化生产线成组技术,阐述了通过度量消费类电子产品相似性和派生性特征,对产线进行成组编码的原理,研究产线工位单元的建模方法,描述了建模内容,并通过有无装载板的产线结构,论述了产线成组编码集成的途径和方法.     

Hygrothermal deformation of orthotropic nanoplates based on the state-space concept

This paper deals with the investigation of the effect of hygrothermal conditions on the bending of nanoplates using Levy type solution model employing the state-space concept. The nanoplates are assumed to be subjected to a hygrothermal environment. The two-unknown function plate theory is used to derive the governing differential equations on the basis of Eringen's nonlocal elasticity theory. The governing equations contain the small scale effect as well as hygrothermal and mechanical effects. These equations are converted into a set of first-order linear ordinary differential equations with constant coefficients. Analytical solution of bending response for nanoplates under combinations of simply supported, clamped and free boundary conditions is obtained. Comparison of the results with those being in the open literature is made. The influences played by small scale parameter, temperature rise, the degree of moisture concentration, boundary conditions, plate aspect ratio and side-to-thickness ratio are studied.     

复合外加剂改性盐石膏的研究

盐石膏的主要成分为无水硫酸钙,其活性差、凝结硬化慢、强度低,需要添加活性剂来激发盐石膏的活性。通过复合外加剂对盐石膏加以改性,并通过XRD和SEM对其作用机理做了分析。结果表明,单掺脱硫石膏和建筑石膏均能缩短盐石膏的凝结时间,建筑石膏的效果较好,但掺量不宜过高。复掺建筑石膏和缓凝剂时,两者比例要控制得当,适宜的建筑石膏和缓凝剂掺量分别为50%和0.10%~0.12%（质量分数）。分析可知,大掺量建筑石膏会增加盐石膏硬化体中二水相和针棒状晶体的含量;缓凝剂掺量的增加,会降低盐石膏硬化体中二水相的含量,棱形晶体增多,从而降低了盐石膏的强度。     

高分散度Pt/C电催化剂的制备

Cabot公司Vulcan XC-72型炭黑，经过H2O2氧化处理后作为Pt的载体，H2PtCl6作为金属前驱体制备了高度分散的Pt/C催化剂。讨论了不同条件下H2PtCl6在炭黑上的吸附性能。载体经过H2O2氧化处理24h,H2PtCl6在pH=9下吸收48h，H2 350℃还原2h，可以制备出铂晶粒平均大小为1.8nm的Pt/C电催化剂。     

DS90C363/DS90CF364 LVDS发送/接收器在数字RGB液晶屏上的应用

通过在FPD铁路上使用LVDS技术可使具有数字RGB接口的液晶显示屏的工作距离大大增加。文章通过一个具体应用环境介绍了21位LVDS发送器/接收器DS90C363/DS90CF364传输套片的主要特性、引脚功能、工作原理，同时指出了在具体设计使用时的注意事项。     

Impact on the photothermal emission from single wall nanotubes by some alkali halide salts

We demonstrate that alkali-halide salts, particularly potassium bromide, can reduce the photothermal emission (PTE) from single walled carbon nanotubes (SWNT). PTE is a prominent spectral feature in Raman spectroscopy when a near infrared laser is used to analyze a dark colored sample. We subsequently show that trapping salts inside SWNT and coating SWNT with the salt has a more pronounced impact on not only reducing PTE, but also enhancing the intensity of the Raman spectral features. The effect, which we have called nanotube enhanced Raman spectroscopy (NERS), has differences and similarities to the widely studied surface enhanced Raman spectroscopy (SERS).     

催化裂化装置生产异戊烯的模拟计算研究

应用HYSIM模拟软件,对催化裂化(FCC)装置获取碳五馏分的各种方案进行了研究,并对各方案的优缺点进行了评述。仅有一套FCC装置的炼油厂或者同时拥有几套FCC装置但各装置稳定汽油辛烷值接近的炼油厂,推荐采用塔底方案。炼油化工型企业可考虑塔顶方案或侧线方案。     

Biotransformation of l‐menthol by twelve isolates of soil‐borne plant pathogenic fungi (Rhizoctonia solani) and classification of fungi

The microbial transformation of l‐menthol ( 1 ) was investigated by using 12 isolates of soil‐borne plant pathogenic fungi, Rhizoctonia solani (AG‐1‐IA Rs24, Joichi‐2, RRG97‐1; AG‐1‐IB TR22, R147, 110.4; AG‐1‐IC F‐1, F‐4, P‐1; AG‐1‐ID RCP‐1, RCP‐3, and RCP‐7) as a biocatalyst. Rhizoctonia solani F‐1, F‐4 and P‐1 showed 89.7–99.9% yields of converted product from 1 , RCP‐1, RCP‐3, and RCP‐7 26.0–26.9% and the other isolates 0.1–12.0%. In the cases of F‐1, F‐4 and P‐1, substrate 1 was converted to (?)‐(1S,3R,4S,6S)‐6‐hydroxymenthol ( 2 ), (?)‐(1S,3R,4S)‐1‐hydroxymenthol ( 3 ) and (+)‐(1S,3R,4R,6S)‐6,8‐dihydroxymenthol ( 4 ), which was a new compound. Substrate 1 was converted to 2 and/or 3 by RRG97‐1, 110.4, RCP‐1, RCP‐3 and RCP‐7. The structures of the metabolic products were elucidated on the basis of their spectral data. In addition, metabolic pathways of the biotransformation of 1 by Rhizoctonia solani are discussed. Finally, from the main component analysis and the differences in the yields of converted product from 1 , the 12 isolates of Rhizoctonia solani were divided into three groups based on an analysis of the metabolites. Copyright © 2003 Society of Chemical Industry